婷婷中文网,999久久久大香蕉,88欧美精品99一区二区三区,日本小姐一区二区视频

當前位置:首頁-新聞資訊

怎么減少鋁單板不必要的浪費呢?

來源:http://guangshe.com.cn/ 發布時間:2023-08-17

鋁單板它在我們生活中的使用是很廣泛的,但是對于鋁單板還有很多行外的人不是很了解,鋁單板它進行加工的時候會經常出現浪費的現象,難免會出現浪費的情況,下面就向大家介紹下:
Aluminum veneers are widely used in our daily lives, but there are still many laypeople who are not very familiar with them. When processing aluminum veneers, there is often waste, which is inevitable. Below is an introduction to everyone:
1.揉捏調直環節
1. Kneading and straightening process
調直這個環節,比較簡略讓型材產生曲折,操作員必定要注意調直所用的力度,假定力度過大就,或許型材就簡略產生變形、收口、桔皮等現象,而力氣過小就會產生型材調不直,構成型材曲折。
Straightening is a relatively simple process that can cause twists and turns in the profile. The operator must pay attention to the force used for straightening. Assuming that the force is too large, the profile may experience deformation, closing, orange peel, and other phenomena. However, if the force is too small, the profile may not be straightened, resulting in twists and turns in the profile.
2.揉捏裝框
2. Kneading and framing
鋁板生產廠家
這個環節也是非常重要的,鋸?fù)甓ǔ唛L度后,一般鋁單板就要進行裝框了,這時應該要注意了:這料是大料仍是小料,是帶管料仍是平面模拉出來的料。
This link is also very important. After sawing the fixed length, the aluminum veneer usually needs to be framed. At this time, it should be noted that this material is large or small, whether it is a tube material or a flat die drawn material.
一般來說,大料和帶管的料抬兩頭裝框不簡略構成曲折,但小料和平面模拉出來的料,抬兩頭就很簡略構成曲折,這時就應該從兩頭向中心挨近進行抬料裝框。但有的型材即便這樣還不可,這時咱們就需要把這類料放在已時效的型材上再抬到框里。
Generally speaking, lifting the two ends of large materials and materials with pipes to frame is not a simple form of twists and turns, but lifting the two ends of small materials and materials pulled out of the flat mold is a simple form of twists and turns. At this point, the material should be lifted and framed from both ends closer to the center. But even if this is not possible for some profiles, we need to place these materials on the aged profiles and then lift them into the frame.
3.表面處理上架
3. Surface treatment on shelf
坯料經時效,硬度已達標,型材不會那么容易變彎曲,但是在上架時還是要注意,兩端抬料時,盡量避免上下大力波動,避免鋁單板出現彎曲的情況。
After aging, the hardness of the billet has reached the standard, and the profile is not prone to bending. However, it is still important to pay attention when placing it on the shelf. When lifting the material at both ends, try to avoid strong fluctuations in the upper and lower directions to avoid bending of the aluminum veneer.
本文由鋁板生產廠家發布,您是不是對這些內容有所了解了呢?更多的內容請點擊:http://guangshe.com.cn我們會有更多精彩內容等你查看。
This article is published by the aluminum plate manufacturer. Have you gained some understanding of these contents? For more information, please click on: http://guangshe.com.cn We will have more exciting content waiting for you to check out.
欧美日韩在线无卡无吗| 欧美伦理激情在线一区| 激情黄色三级小说| 少妇被粗大猛进进出出视| 午夜国内黄片二三区| 无码AV片在线播放| 亚洲视频99| 国产久久中出| 国产一二三四不卡无码久久久| 亚洲综合艹骚货| 亚洲欧美日韩诱| 青青草久久草亚洲国产| 在线国产精品米屯| 麻豆第一区mv免费观看网站| 国产骚受| 久久日韩视频| 99伊人福利视频| 麻豆一区二区在现观看| 浅仓彩音av一区二区三区| 国产色老逼毛茸茸| 少妇吃屌视频| 人妻丰满aV无码久久不长| 色999,国产| 日韩在线人妻视频| 超碰在线小说| 熟妇综合另类| 少妇AAA级久久| 美女www高潮视频91| 99国产精品自在自在久久| 大鸡巴插进小穴电影| 中文一二精品区| 亚洲日韩中午| 琪琪在线,一区二区三区| 国产日添躁久婷| 中国精品久久久久久久电影| av黄色小说在线观看| 国产 欧美 日产中文| 大鸡巴调教人妻在线| 一区二区三区日本视频| 91国产精品久久久蜜臀价格| 久久一区二区电影网|